{"id":717,"date":"2017-03-26T17:10:00","date_gmt":"2017-03-26T09:10:00","guid":{"rendered":"https:\/\/projectkeira.com\/home\/?p=717"},"modified":"2023-07-28T13:38:11","modified_gmt":"2023-07-28T05:38:11","slug":"rigid-industries-d-series-led-driving-lamps","status":"publish","type":"post","link":"https:\/\/www.projectkeira.com\/home\/rigid-industries-d-series-led-driving-lamps\/","title":{"rendered":"Light the Way."},"content":{"rendered":"

Last weekend the nice UPS lady dropped of my brand new Rigid Industries D-Series LED Driving Lamps<\/strong>:<\/p>\n

\"\"
They say brighter is always better\u2026 when it\u2019s dark.<\/figcaption><\/figure>\n

After researching all the different kinds of lamps they have (and they have a lot!) I selected the DOT\/SAE-compliant versions, which meet federal requirements to be used on the road. In other words – they\u2019re street legal, which is what I was looking for since I was going to install them into the factory fog lamp locations and use them for daily driving. These lights have a wide angle and a sharp, flat cutoff at the top. They\u2019re also pretty hefty – the aluminum housings have some weight to them, they feel really solid. One Rigid D-Series is more than twice the weight of the OEM fog lamp and the Morimoto fog lamp<\/a> combined – makes sense seeing as the OEM and Morimoto are almost entirely made of plastic. Here\u2019s a pic of the OEM Nissan fog lamp next to the Morimoto XB-Series Type-S LED lamp, next to the new Rigid D-Series:<\/p>\n

\"\"
Left to right: OEM Frontier, Morimoto XB Type-S, Rigid Industries D-Series<\/figcaption><\/figure>\n

And now let\u2019s get to the install. The first thing I did was remove the Morimoto XB-Series fog lamps from the truck. Next, instead of using the included Rigid wire harness, I made my own custom length harness using 14-ga wire and a relay socket (no pics, it\u2019s boring to look at) and made the necessary connections to be able to run the D-Series lamps off of my factory fog lamp switch. 12v main power and ground were hooked up to my BlueSea fuse block. With the wiring out of the way, it was time to install the actual LED driving lamps. The kit included a Nissan Frontier-specific mounting bracket and hardware, but it\u2019s not 100% bolt-on; some mild modifications needed to be done to the OEM fog lamp brackets. No problem – I used my Dremel and trimmed off the 4 guide tabs on the bracket. Doing this doesn\u2019t affect the OEM fog lamp mounting, so if I ever want to go back to stock, I still can:<\/p>\n

\"\"
Trimmed fog lamp bracket on the left, stock bracket on the right.<\/figcaption><\/figure>\n

Next was the actual D-Series lamp and adaptor plate, which attached to the OEM fog lamp bracket using the OEM Torx screws. The plate had a nice textured finish to it:<\/p>\n

\"\"
Metal adaptor plate attaches to the OEM factory fog lamp bracket.<\/figcaption><\/figure>\n

Finally, the front trim plate. The installation of the front trim plate was simple but there was a noticeable gap between the trim plate and where the mounting screws go. If I tightened the screws too much, it would bend the trim plate. I first used a combination of the included metal washer and five 0.5mm plastic shims to get the spacing just right to where I can tighten down the mounting screws properly. Then I realized I was putting thin plastic shims up against an aluminum heatsink housing (not good!) so I took it all apart again. After a little searching in the garage, I found some 2.5mm aluminum spacers to resolve the issue.<\/p>\n

\"\"
Initially I used plastic shims, then realized the mistake and I replaced them with aluminum, heh.<\/figcaption><\/figure>\n

With the whole thing put together, time to bolt them inside the bumper:<\/p>\n

\"\"
Rigid D-Series assembly installed into the front bumper. King reservoir cameo.<\/figcaption><\/figure>\n

From the outside, they\u2019re not that noticeable or flashy when the truck is just sitting there. The only telltale sign that these are aftermarket is the square lens shape inside a round bumper hole:<\/p>\n

\"\"
Squares in round holes. Okay.<\/figcaption><\/figure>\n

Of course, if you actually look closely, you\u2019ll see the Rigid brand name stamped into the aluminum frame:<\/p>\n

\"\"
They shaped the front trim plate so it won\u2019t block the Rigid Industries name.<\/figcaption><\/figure>\n
\"\"
They turn on, so that meant the wiring was right, heh.<\/figcaption><\/figure>\n

After installing the D-Series LED driving lamps, I spent the next Saturday reconfiguring the wiring of my high beams, D-Series LED lamps, the Xterra Switch<\/a>,<\/a> and the PIAA 520 Lamps<\/a>. Afterward, my front lights now work as follows:<\/p>\n